The leasing personnel of the cold recycling machine remind you that when the recycling machine is in place, taking into account the driving speed requirements of the road engineering maintenance section, the old road surface will be scarified and cold crushed, and stabilizer will be added for sufficient mixing.

在路面銑刨以及材料拌和過程中，應同時操作水車和再生機，確保水車處于空檔狀態，在水帶作用下，與再生機進行連接，并對再生機注水，保證拌和所需水資源充足。

During the process of road milling and material mixing, both the water truck and the recycling machine should be operated simultaneously to ensure that the water truck is in neutral position. Under the action of the water hose, it should be connected to the recycling machine and injected with water to ensure sufficient water resources for mixing.

在拌和過程中，再生機應保持勻速、緩慢行進狀態，對于再生施工速度，應控制在4～10m/min之間。

During the mixing process, the recycling machine should maintain a constant and slow speed, and the recycling construction speed should be controlled between 4 and 10m/min.

在行駛過程中，禁止突然提速或者減速，同時保證行駛過程勻速和連續性，在施工現場安排專人檢查再生機運行狀態，對路面維修施工質量進行檢查，及時發現問題并進行調整。

During the driving process, it is prohibited to suddenly increase or decrease speed, while ensuring a uniform and continuous driving process. A dedicated person is arranged on the construction site to check the operation status of the regeneration machine, inspect the quality of road maintenance construction, promptly identify problems and make adjustments.

此外在維修段路面橫向接縫處理中，加強冷再生機機械設備檢查和維修管理，避免在施工過程中出現停機問題。如果發生停機問題，并且停機時間較長，則當再生機重啟投入施工過程中，應將所有再生設備退再生施工完成的路段1.5m,然后再重新進行材料撒布和施工。

In addition, the inspection and Computerized maintenance management system of the mechanical equipment of the cold recycling machine should be strengthened in the treatment of the transverse joints of the pavement in the maintenance section to avoid Halting problem during the construction process. If there is a Halting problem problem and the shutdown time is long, when the regenerator is restarted and put into construction, all the regeneration equipment shall be returned to the section 1.5m where the regeneration construction is completed, and then the material spreading and construction shall be carried out again.

在縱向接縫處理中，如果縱向?qū)挾仍?m以內，并且縱向重疊部分比較多，則無法進行半幅施工，對此，可采用全幅施工方式，嚴格控制重疊量，提高施工質量以及施工效率。

In the treatment of longitudinal joints, if the longitudinal width is within 7m and there are many overlapping parts in the longitudinal direction, half width construction cannot be carried out. Therefore, a full width construction method can be adopted to strictly control the overlapping amount, improve construction quality and efficiency.

通常情況下，對于重疊寬度，應控制在50～150mm之間，而如果相鄰兩次作業間隔時間在12h以上，則應適當增加重疊量。

In general, the overlap width should be controlled between 50 and 150mm, and if the interval between adjacent operations is more than 12 hours, the overlap amount should be appropriately increased.

在調頭處處理時，應確保機械設備處于已碾壓完成的路面，然后再調頭，并加強調頭作業段保護管理。對于需調頭的8～10m穩定層上，應采用油氈紙或者塑料布進行覆蓋，然后再鋪厚度為10cm的土，后調頭并清理。還有什么事項就來我們網站http://www.wlc189.com咨詢吧！

When handling at the turning point, it is necessary to ensure that the mechanical equipment is on the compacted road surface before turning around and strengthen the protection and management of the turning operation section. For the 8-10m stable layer to be turned around, linoleum paper or plastic cloth shall be used to cover it, and then 10cm thick soil shall be paved, turned around and cleaned. If there are any other matters, please come to our website http://www.wlc189.com Consult!