實際上我們在使用冷再生機過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素，等等一些問題會出現，那么您知道天氣寒冷之前要如何對其進行維護嗎？

In fact, during the use of the cold regenerator, a large amount of dust will fall on the surface of the regenerator, including pollutants such as oil stains stained during construction, which will have a small impact on the appearance. What is more serious is that it will become an inducer of corrosion, and so on. Do you know how to maintain it before the weather is cold?

清洗外表，是工程機械冬季保養要點之一。清洗工程機械的柴油機、底盤、工作裝置的外表,除垢、除油保持再生機的外觀整潔。清洗時嚴禁用高壓、高溫的水槍來沖洗防水要求較高的部位（特別是電器部分），以免造成電器部分的損壞。

Cleaning the appearance is one of the key points of winter maintenance of construction machinery. Clean the appearance of the diesel engine, chassis and working device of the construction machinery, remove dirt and oil, and keep the appearance of the regenerator clean. During cleaning, it is strictly forbidden to use a high-pressure and high-temperature water gun to wash the parts with high waterproof requirements (especially the electrical parts), so as to avoid damage to the electrical parts.

保養轉子及其罩殼和滑靴。檢查轉子是否有水泥結垢等，及時清理灰塵，對需要割除、焊接的刀具及時更換；清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5-10公分，防止雨雪的浸蝕；檢查滑靴，對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。

Maintain the rotor, its casing and slippers. Check whether there is cement scaling on the rotor, clean the dust in time, and replace the cutting tools that need to be cut and welded in time; Clean the dust on the rotor housing, and cushion the rotor housing 5-10 cm above the ground when the vehicle is collected after the construction to prevent the erosion of rain and snow; Check the slipper, repair the worn part of the slipper, and apply grease on the thread to prevent rust.

減速機油位及減速機油的檢查：

Inspection of reducer oil level and reducer oil:

冷再生機租賃廠家提醒您，先切斷電源，等待減速機冷卻后打開放油螺塞，檢查油是否充滿，避免漏油，取油樣，檢查油色澤及粘度指數，如果油明顯渾濁，建議盡快更換。新減速機使用后（500-1000）小時更換新油（將內部污油沖干凈），其后每使用1500小時需要更換油一次，但是在使用過程中，仍需要檢查油的質量，若油有老化、變質情況要隨時更換。

The rental manufacturer of the cold regenerator reminds you to cut off the power supply first, wait for the reducer to cool, open the oil drain plug, check whether the oil is full to avoid oil leakage, take an oil sample, and check the oil color and viscosity index. If the oil is obviously turbid, it is recommended to replace it as soon as possible. Replace the new reducer with new oil (flush the internal dirty oil) after use (500-1000) hours, and then replace the oil every 1500 hours. However, in the process of use, it is still necessary to check the quality of the oil, and replace it at any time if the oil has aging and deterioration.

冷再生機機械在天氣寒冷之前要維護好的相關內容便是這樣了，如果您想要更好更長久的使用設備，就要好好遵守保養維護事項，關注我們http://www.wlc189.com讓您了解更多。

This is the relevant content of the cold regenerator machinery to be maintained before the weather is cold. If you want to use the equipment better and longer, you should observe the maintenance matters and pay attention to us http://www.wlc189.com Let you know more.