移動破碎站吸引人的特點是其強大的生產能力。但是，當移動破碎站的產量降低時，原因是什么，如何解決呢？

The attractive feature of mobile crushing station is its strong production capacity. However, when the output of mobile crushing station decreases, what is the reason and how to solve it?

1.腔體內堆積了太多的材料。

1. Too much material is accumulated in the cavity.

如果物料過濕，則會堆積在型腔內部，這會在加工物料時造成堵塞，從而導致設備效率低下。 如果物料太濕，應進行，然后再進行破碎工作。

If the material is too wet, it will accumulate in the cavity, which will cause blockage when processing the material, resulting in low efficiency of the equipment. If the material is too wet, it should be dehumidified before crushing.

2.振動不穩定。

2. Unstable vibration.

振動不規則以及移動破碎站的振動：錘子可能存在問題。必須及時檢查并在必要時更換錘子。軸承和齒輪聯軸器也可能存在問題。應及時更換以使振動平穩。

Irregular vibration and vibration of mobile crushing station: there may be problems with the hammer. The hammer must be checked in time and replaced if necessary. There may also be problems with bearings and gear couplings. It should be replaced in time to make the vibration stable.

3.成品尺寸不規則。

3. The size of the finished product is irregular.

當顆粒太細時，鉗口中可能有太多錘子或牙齒。然后應減少時間。當顆粒太粗糙時，錘子或鉗口可能會減少，應立即增加。傳送帶太松或電壓不足也可能。在這種情況下，請調節傳送帶的松緊度，檢查電壓功率，然后調節適當的電壓。

When the particles are too fine, there may be too many hammers or teeth in the jaws. Then reduce the time. When the particles are too rough, the hammer or jaw may be reduced and should be increased immediately. It is also possible that the conveyor belt is too loose or the voltage is insufficient. In this case, please adjust the tightness of the conveyor belt, check the voltage power, and then adjust to the appropriate voltage.

4.軸和軸承過熱。

4. Shaft and bearing overheat.

移動式破碎站的軸承受了機器的全部負荷。如果軸承溫度過高，可能是機油不足，則需要添加適量的潤滑油。如果潤滑油被污染，則需要清潔軸承，然后更換潤滑油;如果軸承損壞，則需要更換軸承并降低溫度。

The shaft of the mobile crushing station bears the full load of the machine. If the bearing temperature is too high, it may be due to insufficient engine oil, and an appropriate amount of lubricating oil needs to be added. If the lubricating oil is contaminated, it is necessary to clean the bearing and then replace the lubricating oil; If the bearing is damaged, replace the bearing and reduce the temperature.

如果移動破碎站的潤滑效果不好，容易磨損的零件不能及時更換，維護不完善，上述所有因素都會導致生產不良。如果設備出現故障并進行維護，將會減少產量。

If the lubrication effect of the mobile crushing station is not good, the easily worn parts cannot be replaced in time, and the maintenance is not perfect, all the above factors will lead to poor production. If the equipment fails and is maintained, the production will be reduced.

冷再生機租賃人員認為如果根據潤滑周期對移動式破碎站進行潤滑，將會延長移動式破碎站的使用壽命。

The leasing personnel of the cold regenerator believe that if the mobile crushing station is lubricated according to the lubrication cycle, the service life of the mobile crushing station will be prolonged.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站http://www.wlc189.com并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.wlc189.com And consult our staff, will serve you wholeheartedly.